A Step-by-Step Guide to Setting Up a Bath Tub
A Step-by-Step Guide to Setting Up a Bath Tub
Blog Article
How do you actually feel with regards to Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately tough task. If the old tub is readily accessible, the project can relocate speedily; if you have to open up a wall to eliminate the old bathtub and position the new bath tub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. Instead of employing a contractor to take control of a halfway-completed job, it is better to take into consideration employing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly aid you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your tools and also material list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if called for) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the taps to drain any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the spirit level checks out level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leakages as well as tighten them if needed. Fill the tub as well as also check the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the bathtub must wait till the bath tub has been utilized a minimum of when as this will certainly settle it into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Secure the tap in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The former type must be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can break rather very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very involved in Installing A Bathtub and I am hoping you appreciated the blog entry. Are you aware of another individual who is truly interested in How to Install a Bathtub? Feel free to promote it. Many thanks for your time. Kindly check up our website back soon.
Browse Our Site
Report this page